Aqua’s Hydro systems meet SPIDERFARMER SE 7000

  • Thread starter Aqua Man
  • Start date
  • Tagged users None
Aqua Man

Aqua Man

Staff
Supporter
24,249
638
My man Heywood has a valid point here not gonna lie and I fully expect to see a momma Olenna. Her and Tywin were the best characters imo

I shall speak to the GM on this. I dont know the names she has picked but i do know they are GOT related. She insists that even the 4 that wont make the cut shall be named also.

If these were males it would be easy they would simply be “he who shall not be named” lol

I know im a nerd and im good with that
 
Aqua Man

Aqua Man

Staff
Supporter
24,249
638
Ok so gonna let part of the cat outa the bag here and explain a little about what this system will achieve that will make such an impact on our grows.

First lets explain the concept a bit and dont ask me how because thats not going to be disclosed yet. This will only be about the hydro system but it can be done in any system.

O2 levels in the rootzone are directly related to rate of growth we see in our plants… its no secret and has been proven for decades now.

We are limited to the saturation level of o2 that water will hold and at 70f that’s around 8-9ppm of dissolved o2 under henrys law.

Now so far in a less than idea setup with subpar components @Moe.Red has tested the concept and reached 180% (correct me if im wrong moe) of the saturation of o2 in the rootzone. This is getting much cloaer to aeroponic levels of o2 reaching DO levels almost twice that. Again dont ask me how because im not ready to tell.

Now in my grow system this round with again subpar components i am and anticipating higher than 200% possibly 300% of the max DO saturation. Putting it on par or past aeroponic levels. And this we should see growth rates inline with that but with the safety of a hydroponic system in the event of a failure such as power outage.

By my calculations i should be able to get over 400% the max DO level before release if all goes as planned.

There is a whole nother side to this equipment that adds another dimension of growth increase should you use this in a sealed room… but not going to go into that for the time being.

A huge thank you to @Moe.Red for working with me on this and his ability to manufacture equipment to make data and tgis system possible.

So what you all are watching is more along the lines of research and development in real time thanks to him.

Im very confident in this system now its time to measure the results to take a concept, apply it and either prove or disprove it.

Thanks for being a part of this and watching ppls.
 
Last edited:
Moe.Red

Moe.Red

Staff
Supporter
2,833
263
I know im a nerd and im good with that
The best kind

A732EEEF 035D 4833 AAF4 D831BF6EBB6F


9C552BB5 82FD 421C 9924 129AD1D7AA57


Sensors getting installed now.

4th position is for a light meter still on the bench. Hoping to get an idea of PPDF and Spectrum live during the grow, which is kinda key with these new lights I have that can adjust spectrum and PPFD on the fly.
 
Last edited:
tobh

tobh

Supporter
4,089
263
Day 2 of clones in straight coco.

They are looking great… haven’t seen much on clones started in straight coco but so far it looks like its just like any other media…. Manage humidity and light intensity while keeping the media tight to the stems and moist.

Lux is about 2k

Water line in the tray is just touching the bottom of the tray liner so they can wick up some since coco deies so fast.

I’ll probably go this route in the future especially if im doing coco, hydro, fog or aero.

View attachment 1268504
when i first learned to clone, that how i did it. to this day still consider it the best method as i consistently had 99% success rates within 7 days vs other methods.
 
Aqua Man

Aqua Man

Staff
Supporter
24,249
638
when i first learned to clone, that how i did it. to this day still consider it the best method as i consistently had 99% success rates within 7 days vs other methods.
Good to know brother
 
tobh

tobh

Supporter
4,089
263
YMMV given the age of the plant you took these cuts from but i don't see a reason for failure.
 
GrowHobo

GrowHobo

935
243
My two cents. Stay away from the Floraflex incubator cubes. They look really nice all perfect none smashed or deformed but I think they are too dense. My clone game has gone too shit. I went from 99% successful to like 80% and takes twice as long
 

Similar threads

Zombierider
Replies
31
Views
483
freezeland2
freezeland2
SunshineSupergirl
Replies
4
Views
195
SunshineSupergirl
SunshineSupergirl
SpiderFarmerLED
Replies
586
Views
11K
Brad104
B
BehindEnemyLines
Replies
18
Views
303
BehindEnemyLines
BehindEnemyLines
Top Bottom