Trying To Save A Clone Site Running Cables Other Route.

[bankcee]

So I built a 27 gallon/35 site cloner. But because I have the cable running through one of the sites it bugs me that I lose a site and I believe my lid kind of floods because of that specific site and it's a fucking hassle removing my lid to clean and top off my rez. My OCD wants to run the cable through the bucket it self right under the lid to avoid all these little issues. But I'm unsure as to how to run the cable through and leak proofing that hole because the hole would have to be large enough to run the plug through.. any one got ideas on how I can do this?

 

[Wee Zard]

Yes.
Cut the plug off, or disconnect the other end.
Run the cable through grommets.
Then re-attach one end, or the other.

 

[bankcee]

Yes.
Cut the plug off, or disconnect the other end.
Run the cable through grommets.
Then re-attach one end, or the other.

I don't really wanna do all that wiring and tbh I'm too lazy to learn to do that. Lol

 

[JK420]

Cut the hole and use a Neoprene Puck to cover the hole and hold the cord.

 

[bankcee]

Cut the hole and use a Neoprene Puck to cover the hole and hold the cord.

I thought of that but I didn't wanna cut he hole and it not work and then me have ruined a good tote lol

I'm gonna cut it smaller than a 2 inch though so it's a real snug fit.

 

[Douglas.C]

Notch the lid at the edge, and partially the edge of the bucket if needed. Cutting a hole in the side of the bucket leads to dripping.

 

[bankcee]

Notch the lid at the edge, and partially the edge of the bucket if needed. Cutting a hole in the side of the bucket leads to dripping.

I don't really understand what you mean. I think I do but I'm unsure.. lol

 

[Douglas.C]

Cutting a slot, in the edge of the lid, the width of the cord. Allows the cable to leave the cloner, while still keeping the lid on flat. I've notched the top edge of a container, just enough to allow the cord under the lid, and had it work out ok without dripping. Rather cut a perfect notch in the lid though.

 

[DemonTrich]

I used some foam from a pool noodle. Works perfect.

 

[mandalaman]

I thought of that but I didn't wanna cut he hole and it not work and then me have ruined a good tote lol

I'm gonna cut it smaller than a 2 inch though so it's a real snug fit.

Put the disc inside the bucket not outside

 

[DemonTrich]

If this is the same black base/yellow lid tote, I made the same cloner (see diy subforum).

 

[bankcee]

Cutting a slot, in the edge of the lid, the width of the cord. Allows the cable to leave the cloner, while still keeping the lid on flat. I've notched the top edge of a container, just enough to allow the cord under the lid, and had it work out ok without dripping. Rather cut a perfect notch in the lid though.

yup that's what I thought. that sounds like a good idea might try this out!

 

[hiboy]

You must have slot of free time
How about an extension cord
Hb

 

[mandalaman]

If this is the same black base/yellow lid tote, I made the same cloner (see diy subforum).

Could not find this thread. I have the 27g black and yellow tote would you mind linking it?

 

[DemonTrich]

https://www.thcfarmer.com/community/threads/cloning-machine-solution.79332/page-2#post-1658773

 

[bankcee]

Could not find this thread. I have the 27g black and yellow tote would you mind linking it?

I couldn't find it either lol

 

[DemonTrich]

See above link to my diy.

I've mentioned it before. The footprint of this measly 36 site cloner takes up the same space as 3x of my 25 site cloners I bought from amazon.

 

[bankcee]

anyone sell a built diy cloner before. maybe I'll sell mine and get me a klone king.

 

[DemonTrich]

Yup
Got 300 for mine