THCFarmer.com
121,115 Members Log In Register
Log In Register

What Am I Doing Wrong? Getting Waxy Dry Oil

  • Thread starter Thread starter mikeb437
  • Start date Start date
  • Tagged users Tagged users None

What Am I Doing Wrong? Getting Waxy Dry Oil

mikeb437 24 Replies 3,750 Views
Page 1 of 2 · Replies 1–20 of 25
mikeb437

mikeb437

Posts
592
Reactions
123
Joined
Aug 5, 2009
Points
43
#1
I’m not sure if my temperatures are too high or what but every time I make oil it’s turning into a waxy dried up substance rather than some nice shatter. Can anybody give me some help or advice?
 

Attachments

  • what-am-i-doing-wrong--getting-waxy-dry-oil.jpeg
    what-am-i-doing-wrong--getting-waxy-dry-oil.jpeg
    107.9 KB · Views: 361
  • what-am-i-doing-wrong--getting-waxy-dry-oil-2.jpeg
    what-am-i-doing-wrong--getting-waxy-dry-oil-2.jpeg
    53.9 KB · Views: 311
#5
Bho. Vac purged it in double boiler. I’m not sure what temperature it was at. I was just trying to keep the oil molten so that I would get a reaction in the vac chamber. Every time I would turn the heat lower the oil would harden up too much and nothing would happen. I can still taste a little butane in here So I know it isn’t clean but I do not want this stuff turning into golden crumble. I’m trying to make shatter
 
#8
Ive tried rosin with a curling iron. I found it very hard to Collect the oil off the paper. Naturally i was doing very small buds. And getting small amounts of oil. I need to get out of the butane oil though
 
#10
Looks like a+wax. I vac purge at 95 to 100. At 100 you can handle it. Not sticky but will still bubble. Can take 24 hrs for bubbles to fully pop I have found. Even purged longer at times
 
#11
mikeb437 said:
Ive tried rosin with a curling iron. I found it very hard to Collect the oil off the paper. Naturally i was doing very small buds. And getting small amounts of oil. I need to get out of the butane oil though
Click to expand...
Try making rosin again, but next time freeze the parchment paper with the rosin for a minute or so..then be careful as it will probably be like shatter and fly everywhere. I haven't had anything made with solvent in over a yr..Love that rosin.
I use one of those blue freezer packs when collecting most of the time.
 
#12
I’m not sure if this will work for you. My shatter guy showed me if you take a torch and slightly heat it, glance over it with a flame. You can, I think he said reactivate it. What that means I do not no. But he makes damn good shatter.
 
#14
http://www.originalweedrecipes.com/make-shatter-bho/

This site is one there easier and most clear instructions I’ve come across.
Rather then me repeating it in text.
Read up here and it’s very informative.
Key is good butane. Cheap shit will make crumble like what u see.
Quick check, squirt some in a mirror and let it evaporate, if it leaves a residue. Don’t use it.
Vector is what I have used and it’s stuff is pure .
 
#15
Jack og said:
http://www.originalweedrecipes.com/make-shatter-bho/

This site is one there easier and most clear instructions I’ve come across.
Rather then me repeating it in text.
Read up here and it’s very informative.
Key is good butane. Cheap shit will make crumble like what u see.
Quick check, squirt some in a mirror and let it evaporate, if it leaves a residue. Don’t use it.
Vector is what I have used and it’s stuff is pure .
Click to expand...
as long as you distill your butane use what ever brand you want. And no brand including vector is “pure” they all contain some form of mystery oil
 
#16
To avoid the waxes being extracted you need to work with as cold material and equipment as possible. I'm assuming you're open blasting so investing in a tube with a jacket that you can fill with dry ice and iso mix is a good idea. Freezing your extraction tubes is a must. The butane is important but not the biggest deal. I've gotten golden clear shatter using 5x butane. The main key to your final consistency is your purging process. A double boiler method works but will usually lead to crumble because of the high and uncontrollable temperature. I really recommend a vacuum oven if you're aiming for a nice shatter. That way you can control your temps to keep it low and like @Kfos said, it can take 24 hours to fully purge. You can get most of the butane out just in a heated pan but to get everything out it should be in a vac oven for 12-24 hours with a flip in between.
 
#17
The source material has screwed me a few times when I used a few popcorn buds and trim as a base for BHO. I guess there is a ton of wax in the leaves and that a freezing process will take most of the wax out of the mix, providing a better product. I've never had enough "extra" buds to take a few Oz's and try making decent shatter, so BHO is about as good as I am going to do it, although I just give it a few days to degass since I don't have any vac systems handy.
 
#18
erocknroll said:
To avoid the waxes being extracted you need to work with as cold material and equipment as possible. I'm assuming you're open blasting so investing in a tube with a jacket that you can fill with dry ice and iso mix is a good idea. Freezing your extraction tubes is a must. The butane is important but not the biggest deal. I've gotten golden clear shatter using 5x butane. The main key to your final consistency is your purging process. A double boiler method works but will usually lead to crumble because of the high and uncontrollable temperature. I really recommend a vacuum oven if you're aiming for a nice shatter. That way you can control your temps to keep it low and like @Kfos said, it can take 24 hours to fully purge. You can get most of the butane out just in a heated pan but to get everything out it should be in a vac oven for 12-24 hours with a flip in between.
Click to expand...
It takes a lot longer then 24 hours to properly purge shatter..
 
#19
This is why I never bothered with BHO. Sooo complicated. Pressing rosin is simple. Only two factors, heat and pressure. Have you tried making rosin, you might like it more? I was extracting better than 25% from the right strains. That's comparable to BHO from what I understand of the process.

I'm not a hater. Dabbed a lot of great BHO. But i've made rosin that is stronger than 90% of the BHO I've dabbed.

Good luck brother. What you've made so far looks pretty good to me (reminds me of the low temp 170F rosin I make). Toke up!
 
#20
I know this was asked awhile back but looks to me your pulling waxed or fats. If I were you I would winterize my finished product. This will take that out and make a clear product that will turn to shatter as opposed to that.

I’m sure you can find something on it here if you search or if I search as Greywolf was constantly sharing here as well but this is a known link that I share.
https://skunkpharmresearch.com/diy-and-how-to/
 

Attachments

  • 232A0E0A-99AB-415F-9B6F-5631C26BD891.png
    232A0E0A-99AB-415F-9B6F-5631C26BD891.png
    143.4 KB · Views: 171
  • 11789A5B-454A-4F6D-AAB2-CD4704AC513A.png
    11789A5B-454A-4F6D-AAB2-CD4704AC513A.png
    148.4 KB · Views: 216
Page 1 of 2 · Replies 1–20 of 25
Back
Top Bottom