BB Cheese grow in ProMix Hp | Spider Farmer SE-3000

  • Thread starter PK1
  • Start date
  • Tagged users None
PK1

PK1

Supporter
3,459
263
@Johnlandy420 i soak the plant with the mixture before i send it to flower. However, on my current run i still ran into spider mites problems on the last month of flower.
My plan is to do a smoke run of Sulphur and than take all equipment's down, sanitize with alcohol, repaint the room, and reset all the equipment's.

running indoor has it's pro's and con's and of the con's are that since there aren't any beneficial soldier insects around, these little mites have a better chance of living.
 
PK1

PK1

Supporter
3,459
263
I didn't take a picture of the transplanting but the cup was full of roots. I have her in a bigger butter pot with holes in it. I aLSO started low stress training to give a chance to the lower branches to grow. After all i need four clones from this plant to do a rw run. Feeding at 0.3 ec, temps at 81f and humidity at 65%
2022 04 03 093257
 
PK1

PK1

Supporter
3,459
263
It's been a while a update is made on this due to the flower room getting reset and repainted. Will be dropping two lights in here one of them being SF-3000
I'm planning to setup this room for a rockwool grow. Will install a water bed again, but this time the drain will go into a separate bucket which is the same size of the rez. I'll have the rez outside of the room and with some minor pluming i can bring the water to the plants.

I am aiming to somehow fit my portable AC in the room so I can air cool the room when the door is closed and sealed. Hopefully, if i find a way i can use Co2 in the room, but that's the long shot.

2022 05 12 200511
2022 05 09 145716
2022 05 09 145713

In the middle picture, the mother plant is doing well and the smaller branches are growing better now that three bigger branches were taken as clones. The clones were taken few days a go.
On the right picture is the Wedding Cake in a solo cup. it hasn't rooted well yet, so will keep it in the solo cup for a bit longer. The vpd of this tent is really bad since the tent is half broken.
 
Observationist

Observationist

5,320
313
pictures are taken after feeding, hence why the soil being wet.

Veg day has officially started for BB Cheese. I did remove the lower leaves and the new branches that were being developed, because on transplant day i will burry her main stem more down. Also, since she is going to be a mother plant, I want to make sure that i have nice thick branches as clones. Roots looks nice and growing. Feeding her at 0.5ec for the next few weeks and I will reduce light cycle to 18/6 from 24h
View attachment 1220787
View attachment 1220783View attachment 1220784


While i was at it, i also decided to get some tomato seeds going for the summer. These cherry tomatoes will just go outside in my 5 gallon fiber pots.
View attachment 1220782
I love being able to see the roots, eliminates some guesswork too

I’ve had problems with algae though, not light hitting the roots, yet, didn’t leave in clear long enough maybe for the light to be an issue itself
 
  • Like
Reactions: PK1
Observationist

Observationist

5,320
313
(integrated pest management) preventative measures, before pest “latch on”)

Always, I’d think.

I am after that first outdoor grow mostly got fucked by WPM
 
Stonerbudz

Stonerbudz

490
93
Didn’t know the se3000 fits inside of a 2x2 tent I’m sure it’s pulling a bit on it
 
  • Like
Reactions: PK1
PK1

PK1

Supporter
3,459
263
Ok so, the flower room is setup and we've got the Spider Farmer SF-3000 in the front. I also have a FC-3000 running in the back. Both lights are Mean Well driver GLC 300 and the SP-3000 is the main controllering for both lights. Currently at 3ft high at 15% intensity. I still have some adjusting to do, aiming for 300ppfd

The main valve to the white pvc pipe is closed as i am not running the same setup as last time. I will be using slabs for each rw cube
I've got the angels a bit wrong and the water is puddling on the right but this will be fixed before next update.
I have seperate irigation valves to the mini tubes which feeds each cube.
Rez is a 15gallon with a 220 pump
ph 5.6
ec 0.5
temp unknown at the time
2.4ml z7 enzyme
2ml clearex

i know two lights are overkill at the moment, but i needed to adjust the two lights before adjusting for the plants, but let me know if you guys see anything else that need adjusting.
Have a nice day, until next update!
2022 06 16 170905
 
PK1

PK1

Supporter
3,459
263
Happy Fathers day everyone!

so I moved the cubes on to the single slabs as their final resting home. i let each of the slabs sit in the rez for 20/30 min than made my cuts.
Rez is pretty stable at 5.8 ph with 0.5ec
light is at 2ft with only 150ppfd as one of the clones didn't make it so i made a new cut. it's shity when things don't work out.
2022 06 19 130540
 
PK1

PK1

Supporter
3,459
263
Aight quick update on the light. After talking to Spider farmer, they will be sending me a new light bar to replace the one that went off. I guess the new design does make it easy for replacements if needed. Curently, the rez is stable at 5.6ph 0.4ec and temps at 78f inside rez. I'll be setting a fan for this just so it cools it down na bit more.


2022 06 30 234111
2022 06 30 234111
 
PK1

PK1

Supporter
3,459
263
2022 07 15 223948


clones are growing up fairly quickly now that everything is dialed in. I noticed roots are coming out of the bottom of the uni-slab. The roots coming out of the bottom do look healthy
On these pictures i haven't done any deffoliation or major training. Just been pushing branches and leaves aside, but today i deffoliated and will post a picture at the bottom.
I have also turned on my 2nd light. at 600w im currently pushing 300ppfd across the room.
ph 5.6
ec 0.5
rez temp 78f
current room temp/humidity 82f/55%

2022 07 10 192820
2022 07 10 192808
2022 07 10 192824

2022 07 16 072948
 

Latest posts

Top Bottom