Ground up grow build

[1diesel1]

Floors repaired, walls patched up tomorrow:)

 

[1diesel1]

Walls and floor are complete.
Carbon filter has been relocated above lab cabinets.
Control center has been move to the back corner next to the lab cabinets. Gavita master controller, CO-2 tanks and controller and all other mechanical equipment will be located here.
Tell ya what that carbon filter was a beast to get up there by myself:)

 

[1diesel1]

Had to buy 2 new Gavita 1000de fixtures.
I no, gavitas a bad word.
No choice though, I would have to buy 6 new lights and a master controller for a different manufacturer and that ain’t in the cards rite now.
well, one was broke in the box:(

 

[Moshmen]

Had to buy 2 new Gavita 1000de fixtures.
I no, gavitas a bad word.
No choice though, I would have to buy 6 new lights and a master controller for a different manufacturer and that ain’t in the cards rite now.
well, one was broke in the box:(View attachment 1134627

3 letters for ya -LED lmao sorry brother had to say it . Looking like another sweet room !

 

[1diesel1]

3 letters for ya -LED lmao sorry brother had to say it . Looking like another sweet room !

NO!!

 

[1diesel1]

Makes cleaning a breeze:)

 

[1diesel1]

almost time to get down to business:)

 

[Smithers]

Makes cleaning a breeze:)
View attachment 1134923

Do your floor drain lines route outside? Or do they dump under the building?

I saw them go in after the floor was completed, which was insulated already. Curious where they go. That’s such a sweet setup for cleaning, and for the rest of it also.

 

[1diesel1]

Do your floor drain lines route outside? Or do they dump under the building?

I saw them go in after the floor was completed, which was insulated already. Curious where they go. That’s such a sweet setup for cleaning, and for the rest of it also.

Dumps under the building, I just haven’t finished plumbing them in,

 

[Madbud]

Cheap electric pressure washer might be faster.

 

[ComfortablyNumb]

Just found this thread. Someone looks like they've done this before.
My Uncle was a home builder and I worked summers with him.

 

[1diesel1]

I HATE GUNS AND ROSES!!!
There now that’s out of the way
It’s done
Now for the hard part, finish the veg room project

 

[1diesel1]

 

[Madbud]

Hand watering all those

 

[1diesel1]

Hand watering all those

Yes, I enjoy it, gives me quality time by myself and my ladies:)

 

[Dank.in.Donuts]

1/2 way there with insulation and plywood.
Tomorrow I’ll finish the floor and fully adhere 60 mill. TPO membrane to the substrate.View attachment 893901View attachment 893902

I like that truck bed camper reminds me of the 70s. You didn’t want a 12” slab ?

 

[Dank.in.Donuts]

It’s a shell still got a ways to go. Roof is next. I will be installing 3 inch polyiso rigid board mechanically fastened to the top of the plywood. Then mechanically fasten TPO on top of the ISO. I was wanting to leave the rafters exposed to fasten unistrut for hanging lights and such from the ceiling.View attachment 901243View attachment 901244View attachment 901245View attachment 901246View attachment 901247View attachment 901248View attachment 901249

what about over the door are you going with an awning?

 

[1diesel1]

I like that truck bed camper reminds me of the 70s. You didn’t want a 12” slab ?

If you mean concrete slab,
No, it’s built to move if need be.

 

[1diesel1]

what about over the door are you going with an awning?

No, there’s a gravel drive in front of the door I need to swing trailers around.

 

[Lynch_Ironside]

I just stumbled across this thread…
You’re a mad man!!! Helluva job!
Thanks for sharing and making everyone jealous af lol