Jsd, Gg#4 Hydroponic Research Coco Grow

  • Thread starter Smokey503ski
  • Start date
  • Tagged users None
Smokey503ski

Smokey503ski

1,865
263
Finally was able to build a room. My last round was interrupted by the management company doing a inspection. Had to chop 2 weeks early.
Now that I have a year to play, I built a temporary room.

10'x16'
Mix of 1k and 600 watt HPS.
4 @ 600 watt
4 @ 1000 watt
No Co2
No A/C
2 @ 6" exhaust
Pasive intake
Heat from lights exhausted into house for heat.
3 Gallon grow bags
Coco, Perlite, Hydroton mix
Hydroponic Research HD Nutrients with +Size for flower cycle.

Beginning of veg I used AN Sensi Bloom coco formula.
Jsd gg4 hydroponic research coco grow
Jsd gg4 hydroponic research coco grow 2
Jsd gg4 hydroponic research coco grow 3
I'm just a few days in flower and fed the HR a few days now and already exploding.
This was taken last evening as lights were going out.
Jsd gg4 hydroponic research coco grow 4

And today
 
Jsd gg4 hydroponic research coco grow 5
Jsd gg4 hydroponic research coco grow 6
Jsd gg4 hydroponic research coco grow 7
Jsd gg4 hydroponic research coco grow 8
Jsd gg4 hydroponic research coco grow 9
Smokey503ski

Smokey503ski

1,865
263
Nice looking setup, plants look nice and healthy. Property inspections suck , I had to help a friend tear down a room, box up a bunch of plants and babysit them at my place a couple years ago
Thank you.
Actually it was a blessing in disguise.
A friend of mine let me use her garage to store these ones in while the inspection was taking place. She offered me to use the place as long as I clean out the garage.
It's a 1 car garage. Has a 10'x10' bedroom in the back part.
I will have to upgrade the wiring as it only has 2 15 amp circuits.
So I will be running 2 different spots. Pretty cheap rent at her place. Just need the funds off this one to cover the cost to build the garage out.
The plants I have now are pretty half a room of Gorilla Glue #4 and the other half of JSD.
 
Smokey503ski

Smokey503ski

1,865
263
Need to go back to the drawing board.
I bought some 1/4" soaker hose and made a drip ring out of it.
I have a 2500 gph pump and it wasn't enough pressure to have enough water come out.
Any ideas out there?
 
S

Seed Buyer

665
63
Problem with most the pumps in the industry is they are high flow and not high pressure and do not create enough PSI to push pressure regulate drip emitters. I would get the below in at least 1/2 or 1/3 HP.
 
Smokey503ski

Smokey503ski

1,865
263
Problem with most the pumps in the industry is they are high flow and not high pressure and do not create enough PSI to push pressure regulate drip emitters. I would get the below in at least 1/2 or 1/3 HP.
I ended up drilling around 6-7 holes each in the drip rings I made.
Problem solved the easy way.
I do have to say I'm liking the V+B.
They seem to be stacking pretty well.
 
mancdank

mancdank

8,108
313
I ended up drilling around 6-7 holes each in the drip rings I made.
Problem solved the easy way.
I do have to say I'm liking the V+B.
They seem to be stacking pretty well.
The thing with drippers they always block real quick I always stick some ata clean in the res or I stick it in if I'm using a water wand/lance also the pumps for r/o machines are usually quite strong hope this helps bro
 
Top Bottom