Need help with Co2 gear

[GypsyOutlaw]

I need a little help here. I've never used Co2 enrichment but have recently acquired a couple pieces of gear.
I have no clue what this cylinder thing is with the 110v plug is. Any help is appreciated.
Thank You!

 

[visajoe1]

that looks ancient. could work, should test for leaks with soapy water. or get a new/used one online. also need a co2 controller to plug this into so it maintains desired co2 level during lights on. look around the site for 5-10 minutes, you'll find what you're looking for

 

[GypsyOutlaw]

Seriously no one knows what this cylinder thing with the 110 plug is?

 

[Anthem]

Seriously no one knows what this cylinder thing with the 110 plug is?

The guy above stated the truth. The apparatus you have is just a piece that is needed. It is also the most common part to fail

 

[Mechman60]

I need a little help here. I've never used Co2 enrichment but have recently acquired a couple pieces of gear.
I have no clue what this cylinder thing is with the 110v plug is. Any help is appreciated.
Thank You!

I don't see the logic in co2. Are you going to stop venting air through your grow. If not co2 will just get pushed out.

 

[Anthem]

I don't see the logic in co2. Are you going to stop venting air through your grow. If not co2 will just get pushed out.

If you run CO2 you have to seal up the room. You do not vent

 

[GypsyOutlaw]

I don't see the logic in co2. Are you going to stop venting air through your grow. If not co2 will just get pushed out.

I do t see the logic in your freaking answer to my question

 

[GypsyOutlaw]

The guy above stated the truth. The apparatus you have is just a piece that is needed. It is also the most common part to fail

So you don't know what it is either

 

[GypsyOutlaw]

Got some real winning answers here. For Gods sake I don't know what I'd do without this forum

 

[Anthem]

So you don't know what it is either

Ya I know exactly what it is and I know exactly how to use it. Now you can get up out of bed and figure it out for yourself. If you act like a donkey expect the same in return

 

[Moe.Red]

Got some real winning answers here. For Gods sake I don't know what I'd do without this forum

Don't be a jackass.

I wonder if you could get fuzzier pictures? I went to answer this the other day and gave up because I can't even tell if it was for CO2.

The part right below the gauge is where it screws on to the bottle.

The clear tube above the gauge is where a little ball floats to tell you how much CO2 is being pushed thru the regulator. This is a much lower number than what is on the gauge, which is tank pressure.

The part on the left with the power cord is a solenoid valve that opens the CO2 output (far left) when power is applied. This is how you control it.

I have no idea what the silver thing is on the right. It has no place in a CO2 enrichment system.

I have no idea why there are 3 power plugs. There should only be one.

My guess is that this is not actually for CO2 injection, and it in fact for Tig welding, but I can't even see the damn gauge to take an educated guess.


Now listen. This is not Troll it Up. We are here to help each other as a community and not be dicks to each other. Do that and we will get along fine. But don't come in here half cocked like we owe you something.

 

[Mechman60]

I do t see the logic in your freaking answer to my question

My bad, I just thought you were venting, most do. It's difficult to control my temps without it.
I'll take a pic now so you can see why personally I believe in venting but if what your doing is working by all means go for it. I'd love to see how it works, always keeping an open mind.

 

[GypsyOutlaw]

Ya I know exactly what it is and I know exactly how to use it. Now you can get up out of bed and figure it out for yourself. If you act like a donkey expect the same in return

No you don't but I do. Stop lieing.