Mr Bee
- Posts
- 3,778
- Reactions
- 11,406
- Joined
- Feb 7, 2016
- Points
- 263
no mate i got you.i am a dumb fuck but i understood for a change
no mate i got you.i am a dumb fuck but i understood for a changeYeah the flavor is still there. It’s a cleaner taste vs smoking it in a joint, bong or bowl. Similar to the taste you get from vaping but even a little cleaner than that yet. The smell isn’t as pronounced but still there. Btw I’m talking about making the rosin and then mixing it with PG to vape inside an ecig like device. If you smoked the rosin like a dab then it’s even more pronounced and more like smoking vs vaping.
Sorry if my statement above is a little confusing. I plan on selling the dulytek rosin presses here soon and will make some videos showing how it’s done. From bud to ecig juice in under 15 minutes.
no mate i got you.i am a dumb fuck but i understood for a change
Yikes..I tried to press some freshly JARRED flower and it was way to runny. Your method..(temps, time etc)?I chopped this week. A few of the lowers had powdery mildew so i did an h202 wash on most of it except the perfect top buds. My dryer tent is full and i have a bunch of buds still. I am drying them in the garage with a fan and it is slow because it was higher rh. So I remembered the dulytech and pressed some too moist to smoke but close buds in the dulytec. IT is perfect to get the hang of it.
Wow I can not believe how good it tastes. Better than the shatter i ordered. Amazing white rhino floral fruity rosin. And way stronger than the rosin i ordered. And it is too soon for the buds to taste good in a doob they are green and damp. It wont smoke. I was out and then i though I will give it a shot.
I only need a couple of hits from my wax vape. I am glad i got the press and it is amazing that it is free from chemicals. Thanks for the advice.
I am going to dry it out a bit more and see if it presses more.
In 2-3 hrs..I will have already Rosin pressed an additional 10 grams of flower and probably dabbed most of it too..LOLBoiling water swaps every 15 minutes. Should be evaped in 2 to 3 hours :DView attachment 838157
It was all of the little tiny buds and crap. It wont press for shit. Rosin tastes way better no doubt about it. But the oil tastes just like hash.In 2-3 hrs..I will have already Rosin pressed an additional 10 grams of flower and probably dabbed most of it too..LOL
My real work begins next week..turning some of the summer crop into fresh frozen bubble hash..:p
View attachment 838160
how much do you put on the plates? flowers i mean. 7 grams or so?I run mine at 220 and press for 45 seconds each time. I can press the same material a good three times and then I save the puck to add them together and get even more rosin out. Granted it mixes strains that way but keeps it interesting.
I was kidding..I also press the small buds for more rosin..best use for them is butter though for me..Anyway you do it..as long as it works..enjoy!It was all of the little tiny buds and crap. It wont press for shit. Rosin tastes way better no doubt about it. But the oil tastes just like hash.
It is too bad i didnt know someone that did a lot of rosin pressing so i could see how they do it. But i think it is quality of input. The white rhino outside did not have the trichs like the indoor i grew.
I like the puck maker (this is my 2x4 for the larger presses). It helps prevent blowouts with larger amounts of flower..Yes..lots of good rosin sticks to the bag (make sure to turn the bags inside out before pressing). purepressure.com has excellent videos on this subject and more too. (That's basically how I learned)..I rarely use a bag myself, and confine my presses to RELATIVELY small amounts per press.Do you need that puck holder? I just squeeze it between the two dulytech plates between parchment paper. I found the bags had more rosin in the mesh than i had squeeze out the sides. All a learning curve i am sure.
When i pressed green trim it did taste a lot better though. Like live rosin almost.
Make what? That press? That is the new press and plates (Dulytek 3x6" plates) that I am playing with. My main press is still the Dulytek 6000 electric model. The 2x4 pre-press works well in both (the 6000 has the 3x5 plates)did you buy that or make it ? I think that may help and turn the bags inside out holy shit of course that makes sense.
We use cookies and similar technologies for the following purposes:
Do you accept cookies and these technologies?
We use cookies and similar technologies for the following purposes:
Do you accept cookies and these technologies?