TEMP/VAC OVEN THREAD

SCFSYNDICATE760 · Jul 1, 2012

whats up oilers...just grabbed a vac oven...dont have enough experience w temps n stuff...i know obvioulsy dont wanna burn it....anyone else use a vac oven? things fuckin pimp! works pimp!

just wanna know what other people are using temp wise...

hammalamma · Jul 1, 2012

It seems to me the strain used is a big factor in deciding temps. I would have to say 110f to 140f. Also the time you are going to leave under vacuum is important, less time in vacuum more heat or less heat more time in vacuum.

Glab120 · Jul 1, 2012

Ive never seen a vac oven. can you show us some pics of it in action? what temps to run it at also depends on the consistency you want. if its honeycomb or budder your after that will require higher temps usually around 140 below that you'll get a shatter or wax.

hammalamma · Jul 2, 2012

This pic is the first time I used it, its not mine but I have full access to it and have done a few more pulls with it now.I have to keep it real low, like 1.5 or lower. Shatter is my preferred outcome.

Glab120 · Jul 2, 2012

that's a cool setup. Ive found getting a very stable shatter is one of the hardest consistency to achieve. the temps will need to be just under were it wants to turn into a honeycomb. i find that most amber glass is still way under purged. if it instantly sticks to your fingers and is very stringy an hard to work with its not done. you should be able to grab a chunk of shatter and break it up with out it melting onto you fingers.

SCFSYNDICATE760 · Jul 2, 2012

yea thats about what i was thinking...
that one is almost exactly what i have, except w a stronger pump

hammalamma · Jul 2, 2012

Glab120 said:
that's a cool setup. Ive found getting a very stable shatter is one of the hardest consistency to achieve. the temps will need to be just under were it wants to turn into a honeycomb. i find that most amber glass is still way under purged. if it instantly sticks to your fingers and is very stringy an hard to work with its not done. you should be able to grab a chunk of shatter and break it up with out it melting onto you fingers.

I agree, it's all about thin film purging. Not just the butane but also the moisture.

ogplatinum · Jul 2, 2012

Link to where one could get one of these? They look PRIME!

SCFSYNDICATE760 · Jul 2, 2012

got mine on ebay...thats why i want a rotovape...helps to purge thinner layer...also keeps it moving...
which brings me to another thing...
i have been moving physically my chamber to allow the oil to run while purging...this seems to helo make it thinner thus helping bubbles form and pop easier ....
anyone else experience or mess with this....that vac oven is pretty awkward to tip but it does work and help i think...

the only problem w a roto is then you gotta get the oil out of the beaker, so u either gotta use a carrier solvent or a flask that has a break in it....or a flask that ha a huge opening, just not sure what biggest or biggest machine will hold is...

pugliese63 · Jul 3, 2012

Thanks for sharing, I'm amazed at how precise the techniques are becoming to make concentrates. This is the kind of info that really moves things forward for us all. I'll be trolling ebay now. Like yourself I've been looking into rotovaps. Seems it would be the perfect solution but I have to agree with you on the getting the oil out. I'll be interested to see what you come up with in the future.

Future · Jul 3, 2012

And here I am boiling water and a heating skillets, must find one

SCFSYNDICATE760 · Jul 4, 2012

Future said:
And here I am boiling water and a heating skillets, must find one[/quote
yea fuck all that water heating n shit...
i wanna do least amount of steps...
i dont even blast onto glass anymore, parchment only..fuk scraping...loljust blast onto paper lined dish, and right into the vac oven...few minutes....DING! done...

ANY SCIENCE TYPES KNOW IF THIS WILL WORK WITH A ROTOVAPE?GW?
yea my solution to roto prob is getting this pimp flask that comes apart in the middle....perfect i think? well see

Future · Jul 4, 2012

^ HAHAHA!!! Tell me why my partner put me onto shooting straight to parchment and I haven't looked back since!

1971 · Jul 4, 2012

i found that when i poured onto parchment, it soaked through and made a freaking mess :/

SCFSYNDICATE760 · Jul 4, 2012

"soaking" through the parchment paper is an impossibilty...
there was either a hole or you somehow let oil slip between a crack or something or there was oil in the pan previously...
its designed specifically to have stuff not soak through it...
i do it every night, the only time i have an issue is if theres a rip i didnt see in the paper (does happen and will seem to leak through then u got a piece of paper with oil on top n bottom n a big fuckin mess....so you gotta be carefull)
but i assure you if you do this properly its the easiest way, maybe next to the bag tech...
you dont even really need teflon, i blasted right into a ziplock n it worked fine...
u wanna use a freezer bag at least tho...

pouring it tho does work, i did that a few times at first...then you are losing a lil when you pour tho...best is just line reseptacle w paper...heres a pic..
make sure ur not using wax paper use parchment paper..
see really simple
line dish then blast then you just pop it out n open it up..walla then stick in vac oven...done

1971 · Jul 5, 2012

very nice! thx for the pics

i'll have to try again then :)

SCFSYNDICATE760 · Jul 5, 2012

no prob! hope it helps...ask a ? anytime if u try it and like it...ive messed around a bunch with it..

1971 · Jul 5, 2012

i can't wait to make some oil with this fresh crop coming in versus the aged stuff i've been using

thank you again!

Glab120 · Jul 5, 2012

SCFSYNDICATE760 said:
no prob! hope it helps...ask a ? anytime if u try it and like it...ive messed around a bunch with it..

That's a cool step spraying strait onto the parchment seems like it work perfect for that vac oven. I did that along time ago but thought it was to messy trying to get it scraped together at first. My question is do u vac purge your oil without heat the first couple times till it's a stabel muffin or do u add heat and just let it bubble?
I ask cuz I skipped this step earlier and it seemed to make my purging process take forever. My oil was just bubbling at 140 degrees for several hours without waxing up.

1971 · Jul 7, 2012

140 seems awful hot for vac purge. seems like people are trying to keep the temps as low as possible. just picked up some oil slick pads... will try them out later today

TEMP/VAC OVEN THREAD

TEMP/VAC OVEN THREAD

SCFSYNDICATE760

hammalamma

Glab120

hammalamma

Glab120

SCFSYNDICATE760

hammalamma

ogplatinum

SCFSYNDICATE760

pugliese63

Future

SCFSYNDICATE760

Future

1971

SCFSYNDICATE760

1971

SCFSYNDICATE760

1971

Glab120

1971

Privacy & Transparency

Privacy & Transparency