THCFarmer.com
121,256 Members Log In Register
Log In Register

Rapid rooter and watering auto...

  • Thread starter Thread starter Irishguy83
  • Start date Start date
  • Tagged users Tagged users None

Rapid rooter and watering auto...

Irishguy83 646 Replies 65,742 Views
Page 24 of 33 · Replies 461–480 of 647
#461
Ok got the kit but I need some more tape..... but right now watered her ppm 458 ph @ 5.68..... I took some bottom leafs off and I'm trying to get this fucking thing hooked up because I'm totally going strong check these pics....
20191207 130303
20191207 130303
20191207 130241
20191207 130231
 
#463
Aqua Man said:
That thing is a mutant... I love it bro.
Click to expand...
Oh and it took me a minute to get it figured out to get that kit out my window and the ducting clamps sucked so I busted out my medical tape and taped the 6" to the 5" inside and it's a stretch but I works for now until I can seal it.... small gaps nothing huge..... so weather stripping should do it.
 
#464
Irishguy83 said:
Oh and it took me a minute to get it figured out to get that kit out my window and the ducting clamps sucked so I busted out my medical tape and taped the 6" to the 5" inside and it's a stretch but I works for now until I can seal it.... small gaps nothing huge..... so weather stripping should do it.
Click to expand...
Git R Dun! 👍 👍 👍
 
#465
Ok so everything has been running good I just put in another prefilter..... just easier to buy a new one.... so my RH wont drop below 55% and room temp 75f........ I have plenty of fresh air and exhausting out of my vented window.... I'm here @ the end what do I do?
 
#466
Ok so today I've had to trim due to humidity can you guys give me more tips on trimming....
20191208 135645
20191208 135630
20191208 135608
20191208 135608
 

Attachments

  • 20191208_135542.jpg
    20191208_135542.jpg
    201.4 KB · Views: 44
#467
Irishguy83 said:
Ok so today I've had to trim due to humidity can you guys give me more tips on trimming....View attachment 918830View attachment 918832View attachment 918833View attachment 918833
Click to expand...
If your maxed on airflow you can try to lower the humidity in the room the tent is in. If not make sure you have good airflow throughout the plant and you should be fine. It's not like you have huge buds yet. Airflow will be key to preventing mold. The risk is a little higher in higher humidity but with good airflow 55% should not be an issue unless you get huge buds near the end. They will slow down drinking in a bit so I think you should be fine.
 
#468
Aqua Man said:
If your maxed on airflow you can try to lower the humidity in the room the tent is in. If not make sure you have good airflow throughout the plant and you should be fine. It's not like you have huge buds yet. Airflow will be key to preventing mold. The risk is a little higher in higher humidity but with good airflow 55% should not be an issue unless you get huge buds near the end. They will slow down drinking in a bit so I think you should be fine.
Click to expand...
The past day or2 she has been slowing down on drinking .... instead of twice in a day only once
 
#470
Aqua Man said:
There ya go humidity should get a bit easier to manage over the next week
Click to expand...
Yeah that's what I was worried about I have everything setup and perfect.... so I think that with me trimming her because I'm going to keep trimming to make it more airy....
 
#471
Is it ok to trim off all sun leaves the ones that reach off but dont have hairs on them at all?
 
#472
Irishguy83 said:
Is it ok to trim off all sun leaves the ones that reach off but dont have hairs on them at all?
Click to expand...
I would remove leaves that are stacking first. I prefer to remove as little as possible and still make sure I have good airflow through the plant. If I'm gonna remove move I would start and the bottom and thin up a bit. The plant uses all leaves to make and store nutrients so even if they don't appear to be getting much light they are important. But good airflow I put above this. So I say take what ya need but only what ya need to ensure you get good airflow and avoid possible mold issues.
 
#473
Ok so I did a res change yesterday ppm 390 ph @ 5.76 RH @ 51% just kicked my auto mode to stage 10 to see if that finally works its loader for sure lol...... but she looks great I've got tricomes on the buds and the leafs on buds....
20191210 125135
20191210 125115
20191210 125056
20191210 125045
20191210 125041
20191210 125038
20191210 125030
 
#474
Just for note today I just did a check she took only 1/4gal of mixture and a light mixture she seems to like ppm of 330 to 390 to I adjusted to 378 today ph was @ 7.03 took it down to 5.76...... but looking amazing and tasty already..... and totally amazing watching all my work come together here at the end....
 
#475
Irishguy83 said:
Just for note today I just did a check she took only 1/4gal of mixture and a light mixture she seems to like ppm of 330 to 390 to I adjusted to 378 today ph was @ 7.03 took it down to 5.76...... but looking amazing and tasty already..... and totally amazing watching all my work come together here at the end....
Click to expand...
Question about my temp/humidity sensor I've had it just over the canopy but also under the light is that correct placement or do I have that wrong to where that's why it would slow down?
 
#476
You have done a bang up job so far man... It's looking great!

In regard to sensor placement. It should be about canopy level but out of the light source and away from the leaves. It's likely giving you a bit warmer temps and higher humidity readings because of this. I can give you a ghetto fix if ya like haha but don't laugh
 
#477
Aqua Man said:
You have done a bang up job so far man... It's looking great!

In regard to sensor placement. It should be about canopy level but out of the light source and away from the leaves. It's likely giving you a bit warmer temps and higher humidity readings because of this. I can give you a ghetto fix if ya like haha but don't laugh
Click to expand...
So more by the tent wall?
 
#478
Aqua Man said:
You have done a bang up job so far man... It's looking great!

In regard to sensor placement. It should be about canopy level but out of the light source and away from the leaves. It's likely giving you a bit warmer temps and higher humidity readings because of this. I can give you a ghetto fix if ya like haha but don't laugh
Click to expand...
I have plenty of places to hang it from
 
Page 24 of 33 · Replies 461–480 of 647
Back
Top Bottom