UnderDawg Numero Uno

[mittenmedgrow]

Plants are looking good. I wouldnt reveg unless you have to.

 

[winta]

mitten aint tellin u no lies bro cut now or forever hold your piece unless u reveggin ;)

Hey andy cut them clones now. The furter they get into flower its going to confuse them.

Plants are looking good. I wouldnt reveg unless you have to.

 

[Shady]

Good job brah! I'm excited to see the bad ass females lift up their skirts and get pretty for the show... :makeup

 

[sticky icky]

Wazzup Playa lookin real good bro wish I new about the thread earlier would've been poppin in real nice fat ass dark leaves bro can't wait to see these poppin gonna be some fire dawg!

 

[andy107]

Plants are looking good. I wouldnt reveg unless you have to.

Thanks bro, ill be sure to take some cuts tomorrow.

mitten aint tellin u no lies bro cut now or forever hold your piece unless u reveggin ;)

Ima cut some clones off of em tomorrow dude, any of these lookin like the ones you ran?

Good job brah! I'm excited to see the bad ass females lift up their skirts and get pretty for the show... :makeup

Thanks man, stick around should be some dank on the way!

Wazzup Playa lookin real good bro wish I new about the thread earlier would've been poppin in real nice fat ass dark leaves bro can't wait to see these poppin gonna be some fire dawg!

its all good man, better late than never! thanks for droppin in!

 

[winta]

yea your female, #3 and #1 look like the phenos i found! cant wait to see how yours turn out!

Ima cut some clones off of em tomorrow dude, any of these lookin like the ones you ran?

 

[andy107]

4 seeds, 4 females nuff said. haha feel like i hit the lotto! I took 1 cut off each plant today and they look pretty stressed (real droopy) but im hoping they will snap out of it in a couple days.

 

[mittenmedgrow]

Cool. The cuts should perk back up. Just keep the humudity and temp up. Is this your first time taking cuts?

 

[andy107]

Cool. The cuts should perk back up. Just keep the humudity and temp up. Is this your first time taking cuts?

it might as well be..this will be the third time ive tried cloning but the first time i tried i drowned them and the second time the temps were too hot..so hopefully ill put it off this time.

 

[mittenmedgrow]

Ya cloning is tricky for some people. Once u figure out what works for you it will be easy. If you want any help let me know.

 

[sticky icky]

Wut up brotha maybe look into pickin up a small site eazy cloner its so easy to deal with no spraying no domes just changin water n cleaning.

 

[andy107]

seems like their getting worse, is this normal for cuttings to be looking like this?
Temp is 80 F and the humidity is 40% ..i feel like i need to raise my humidity?

 

[mittenmedgrow]

Is your dome fogging up?

 

[Shady]

Word... Your humidity should be over 80% in the dome... Fogged to the point you can't see inside... :cool

 

[andy107]

Is your dome fogging up?

yea it gets foggy when i mist it but it doesnt stay misted/fogged very long.

Word... Your humidity should be over 80% in the dome... Fogged to the point you can't see inside... :cool

any ideas on how i can get my humidity up there? would a warm wrag work?

 

[Shady]

Get a $20 seedling heat mat and add a bed of perlite in the tray with enough water at the bottom to barely touch the bottom of the rapid rooters... I'm about to take some clones soon and will write another shady cloning technique tutorial which I've posted a few times in my journals... :cool

 

[andy107]

I already have one of those heating mats, but i dont have perlite. would it still work without the perlite?

 

[mittenmedgrow]

Yes, I like the perlite idea but u dont need it. You want just enough water to touch the bottom of the plugs.

 

[Shady]

You don't need the perlite as I've never used it before, but since I started using the heat mat last month, I've discovered that it tends to be too hot and the water will need to be replaced more frequently... Of course this heat differential depends on the room's ambient temps so the perlite should add a buffer to slow down evaporation and reduce too much heat transfer to the clippings. In lieu of the perlite some spacers can be used between the heat mat and tray if it's too hot... In this scenario I would add enough water to fill the grooves on the tray... :thinking

 

[sticky icky]

Hey Andy did you send the mom into 12/12 yet those look history bro you need to take a couple more cuts.