ComfortablyNumb
- 6,099
- 313
Well, we never know, do we?pulling up with some and the expectation that this thread goes nowhere.
Well, we never know, do we?pulling up with some and the expectation that this thread goes nowhere.
-Lighting is in the mailpulling up with some and the expectation that this thread goes nowhere.
general observations so far:
- big project without clearly defined scope
- problems identified early on with no clear solutions, because of lack of scope
- realizations that lighting, humidity, heat, cooling, ventilation haven't been figured out
- plant count/scale not defined
- trying to be discrete yet massive hole in the ground
looks like a trainwreck and likely a dead thread in a month, but signing up for the show. godspeed to OP, just hope lessons are learned and a successful end comes from the means expended.
I'm a big K.I S.S. guy (Keep It Simple Stupid)I am working on a greenhouse design currently, and Every time I get the thing drawn and printed, he sees something else he wants to do.
There is no way I would dig a hole until I knew exactly what i was going to stick in it and in what order. It's too big of a project because there are a hundred tiny details that make all the difference. You need a written plan.
On the other hand, my uncle would begin digging before he had the plans. He dug basements for a living. Him, I've seen do stuff, but he has eons of experience.
Hey rock haven’t seen ya around it a bit. Glad to hear from yaplease do keep us updated, ive got somme grow buddies who have the same setup with 4-20'containers inline,I helped with the exhaust fans and ventilation.They didnt realize the moisture and dampness aspect until after it was done,did some custom S/M work for them around the penetrations,basically overkill to make sure it was gonna draw in water within times of neg pressure,what previous guy said if theres water it will find a way in
I thought about using a fog machine inside for like 30 minutes then pressurizing the container to find any leaks after waterproofingplease do keep us updated, ive got somme grow buddies who have the same setup with 4-20'containers inline,I helped with the exhaust fans and ventilation.They didnt realize the moisture and dampness aspect until after it was done,did some custom S/M work for them around the penetrations,basically overkill to make sure it was gonna draw in water within times of neg pressure,what previous guy said if theres water it will find a way in
Water accumulation has definitely been a factor I am expecting to deal with. When I shot grade I've got just over 1% in my pit so I can be sure it accumulates away from my plants into my work area. I've got a pump here ready to go.Didn’t read the entire thread but you better design a hell of a sump with a main pump and a backup before you even put the container down. Use concrete footings at least 48” deep to set it on.
Personally I’d stay above ground and insulate the piss out of it. Stack bales of wheat straw around it and over it. Make the thing waterproof all the way around.
Living in country with frequent earthquakes I’m probably too deep into securing anything from lateral movement.Water accumulation has definitely been a factor I am expecting to deal with. When I shot grade I've got just over 1% in my pit so I can be sure it accumulates away from my plants into my work area. I've got a pump here ready to go.
As for a footing. Having been in the construction industry my whole life I didn't see it as necessary considering my region. Frost won't be a factor, what has potential to he an issue is the unit floating up but I've got plans already for that. Driving 30" anchors on all four corners that I then tether to.
Also I'm going to weld 1' brackets 4' apart all down the outside so after I fill it all in they too will be held in place by the surrounding clay.
If we were neighbors we could build one heck of a grow op together
Good stuff. You going to lift the matson and spray the bottom?I started waterproofing today.
Coat one of three applied.
I found this product at a local hardware store, seems to he just what i need. The unit used to be blue and green.
So the bottom actually is where most of the strength is. I will be flipping the unit upside down, waterproofing it and then filling the channels with concrete and waterproofing it again. There are beams that run short ways maybe 1 foot apart in the current floor so doing this is the best way to bury a shipping container. Other guys didn't go as far as filling the channels with concrete but I will be doing so.Good stuff. You going to lift the matson and spray the bottom?
Grew up in a blacksmith and welding shop. Working as did my younger brother. Pop didn’t hire anyone during summer. Repairing farm equipment and building Class III custom hitches.So the bottom actually is where most of the strength is. I will be flipping the unit upside down, waterproofing it and then filling the channels with concrete and waterproofing it again. There are beams that run short ways maybe 1 foot apart in the current floor so doing this is the best way to bury a shipping container. Other guys didn't go as far as filling the channels with concrete but I will be doing so.
I've never understood why people cut their work short. It always ends up costing more time and money doing it the cheap and fast way, always. I understand on certain levels of knowledge, like my thinking initially a little T6 would be all the venting I need. But I didn't hesitate to order $750 worth of material just to get sufficient airflow.Grew up in a blacksmith and welding shop. Working as did my younger brother. Pop didn’t hire anyone during summer. Repairing farm equipment and building Class III custom hitches.
Later in life I modified a Harley frame for a shop. It was not my first work for them. The guy picking it up “Damn. You and Mickey do everything like it’s on a damned battleship.”
Do it right the first time. Keep going. You and I could work together I’m sure.
Seems like one of these could possibly be constructed out of a simple solar panel and a cheap air pump. You could likely build one with some junk you have laying around and approximately $50 in supplies... ie. PVC pipe... The water seer looks like a scam from where I stand, unfortunately. It's mindboggling that a good idea's like these (that can solve real world problems) are hijacked by greedy fucks simply out to make a buck.You could use an air well and an underground storage tank for water.
Connect the tank directly thru the wall.