Lost's MPB's

Lost · Jan 22, 2010

BOSSMAN88188 said:
Just drove from HD to HD.
I guess tote season Is over. WTH
Found em and picked up 10. Thanx again bro.

Shit, i guess i'll wait a week to get more.. Did you try any of the HD's north of me?

squarepusher · Jan 22, 2010

northone said:
nice photos and setup
those uniseals look good....
will be looking in on this one

is he using uniseals?

if so, what size, also what type of tubing is that? (name and size)

Lost · Jan 22, 2010

The seals are general hydroponics seals the inner diameter is 1 1/4, outer is 1 3/4 ish. I just went to home depot and took the seal with me. Its expensive tubing, 3 dollars a foot, but its stron stuff and it works perfectly with the seals.

The good thing about the seals is they are available at most hydro stores and are available thru sunlight supply, on of the big distributers. The seals will run you about 2.50 each and you need 2 per bucket.

kushpheen · Jan 23, 2010

Hey lost whats the device you have pictured next to your air pump?
What size res would you recommend for 7 plants, same HD tubs as yours?
Are you using 3 gallon pots or the 10" net pots?

Lost · Jan 23, 2010

kushpheen said:
Hey lost whats the device you have pictured next to your air pump?
What size res would you recommend for 7 plants, same HD tubs as yours?
Are you using 3 gallon pots or the 10" net pots?

The black box is a prime 1/3 HP modular chiller. I keep my res set at 65 degrees. For a 7 plant system I would reccommend 2 low profile 100 gallon (115 is perfect, but hard to find and expensive). Remember they have to be low profile. I think DD's sinks his into the floor but I cannot do that, im on a conceter slab.

I use 10 inch netpots and a 5 gallon bucket with the top cut off and pushed thru the lid. If you look at my tub girls thread I have a lame ass how to on it. :)

Lost · Jan 23, 2010

One thing I was to poin out is that the res is only 1/5th full when running. The reason for such a huge res is that if your pump fails or the electricity goes out, I would over top the res. I could put a check valve in place and I will probablly do that but its nice to fill up the res, mix the nutes, and hit the switch on the pump and I can walk away. The check valve will be a nice addition when I can find a nice barbed one. Cant seem to find any around here... The res ends up haveing about 20-25 gallons in it while running so the pumps will function.

mrdizzle · Jan 23, 2010

i hooked up the check valve and it will improve your life a great deal, allows the system to hold 2x more water, im only topping mine once or twice a week. i found it at a pond store and i had to glue in the barbed fittings but its really great. it also keeps water in the tubs incase of a power outage, so the roots dont dry out.

kushpheen · Jan 23, 2010

Whats that white box sitting next to the airpump on top of the chiller?

Just got my check valve yesterday, thanks for the tip diz...

wonderinalice · Jan 23, 2010

Hey lost....

The large clear tubes...like 2 1/2 or 3" kinda looks like the flexible pvc i use for outdoor ponds/waterfalls ....Don't know if you get any of your stuff from a pond/waterfall store....but i know they carry a black tubing 2 1/2 and 3" at almost every pond store i've been..looks like it would work perfect for what your doin...and they usually carry all kinds of fittings...I buy a lot of compression fittings for installs that require no glue....Hope it helps! ..thanks for the great post!

Lost · Jan 23, 2010

kushpheen said:
Whats that white box sitting next to the airpump on top of the chiller?

Just got my check valve yesterday, thanks for the tip diz...

The white box is the thermostat for the chiller and the black box is the UV sterilizer for the chiller. I run it occationally.

Ok, next week I'll go check valve hunting. Thanks for the info KP!

easypleasie · Jan 23, 2010

My local Lowes has pvc check valves in 1/2" to 2" sizes. Small price to pay for peace of mind!

Lost · Jan 23, 2010

Im on it tommorrow EP! Thanks for the heads up ^^!

Boots Sugarleaf · Jan 23, 2010

I get the brass check valves at the local hardware for 'round $10 each depending on size, then I screw in the barb fittings and connect to the hoses

Lost · Jan 23, 2010

Boots Sugarleaf said:
I get the brass check valves at the local hardware for 'round $10 each depending on size, then I screw in the barb fittings and connect to the hoses

I'll check it out tommorrow, thx.

kushpheen · Jan 23, 2010

Brought to you by the check valvers of america...lol

Lost · Jan 24, 2010

Well, here is what I built. Check valve and bypass for res changes..

Thoughts?

mrdizzle · Jan 24, 2010

i love it, make sure the check valve is the right side up otherwise it wont swing closed, should say this side up on the check valve

convex · Jan 24, 2010

That looks like it should do the trick!

Boots Sugarleaf · Jan 24, 2010

Lost said:
Well, here is what I built. Check valve and bypass for res changes..

Thoughts?

exactly like what I do, 'cept I use flexible tubing....looks good

squarepusher · Jan 24, 2010

Lost said:
Well, here is what I built. Check valve and bypass for res changes..

Thoughts?

rep

Lost's MPB's

Lost's MPB's

Lost

squarepusher

Lost

kushpheen

Lost

Lost

mrdizzle

kushpheen

wonderinalice

Lost

easypleasie

Lost

Boots Sugarleaf

Lost

kushpheen

Lost

Attachments

mrdizzle

convex

Boots Sugarleaf

squarepusher

Privacy & Transparency

Privacy & Transparency