That thing is a mutant... I love it bro.Ok got the kit but I need some more tape..... but right now watered her ppm 458 ph @ 5.68..... I took some bottom leafs off and I'm trying to get this fucking thing hooked up because I'm totally going strong check these pics....View attachment 918542View attachment 918542View attachment 918543View attachment 918544
Oh and it took me a minute to get it figured out to get that kit out my window and the ducting clamps sucked so I busted out my medical tape and taped the 6" to the 5" inside and it's a stretch but I works for now until I can seal it.... small gaps nothing huge..... so weather stripping should do it.That thing is a mutant... I love it bro.
Git R Dun!Oh and it took me a minute to get it figured out to get that kit out my window and the ducting clamps sucked so I busted out my medical tape and taped the 6" to the 5" inside and it's a stretch but I works for now until I can seal it.... small gaps nothing huge..... so weather stripping should do it.
If your maxed on airflow you can try to lower the humidity in the room the tent is in. If not make sure you have good airflow throughout the plant and you should be fine. It's not like you have huge buds yet. Airflow will be key to preventing mold. The risk is a little higher in higher humidity but with good airflow 55% should not be an issue unless you get huge buds near the end. They will slow down drinking in a bit so I think you should be fine.Ok so today I've had to trim due to humidity can you guys give me more tips on trimming....View attachment 918830View attachment 918832View attachment 918833View attachment 918833
The past day or2 she has been slowing down on drinking .... instead of twice in a day only onceIf your maxed on airflow you can try to lower the humidity in the room the tent is in. If not make sure you have good airflow throughout the plant and you should be fine. It's not like you have huge buds yet. Airflow will be key to preventing mold. The risk is a little higher in higher humidity but with good airflow 55% should not be an issue unless you get huge buds near the end. They will slow down drinking in a bit so I think you should be fine.
There ya go humidity should get a bit easier to manage over the next weekThe past day or2 she has been slowing down on drinking .... instead of twice in a day only once
Yeah that's what I was worried about I have everything setup and perfect.... so I think that with me trimming her because I'm going to keep trimming to make it more airy....There ya go humidity should get a bit easier to manage over the next week
I would remove leaves that are stacking first. I prefer to remove as little as possible and still make sure I have good airflow through the plant. If I'm gonna remove move I would start and the bottom and thin up a bit. The plant uses all leaves to make and store nutrients so even if they don't appear to be getting much light they are important. But good airflow I put above this. So I say take what ya need but only what ya need to ensure you get good airflow and avoid possible mold issues.Is it ok to trim off all sun leaves the ones that reach off but dont have hairs on them at all?
Question about my temp/humidity sensor I've had it just over the canopy but also under the light is that correct placement or do I have that wrong to where that's why it would slow down?Just for note today I just did a check she took only 1/4gal of mixture and a light mixture she seems to like ppm of 330 to 390 to I adjusted to 378 today ph was @ 7.03 took it down to 5.76...... but looking amazing and tasty already..... and totally amazing watching all my work come together here at the end....
So more by the tent wall?You have done a bang up job so far man... It's looking great!
In regard to sensor placement. It should be about canopy level but out of the light source and away from the leaves. It's likely giving you a bit warmer temps and higher humidity readings because of this. I can give you a ghetto fix if ya like haha but don't laugh
I have plenty of places to hang it fromYou have done a bang up job so far man... It's looking great!
In regard to sensor placement. It should be about canopy level but out of the light source and away from the leaves. It's likely giving you a bit warmer temps and higher humidity readings because of this. I can give you a ghetto fix if ya like haha but don't laugh
Yeah that will work but not to close it touchingSo more by the tent wall?
Ok I'm going to bring it to the corner right inside to the right so its away from intake and the fan also and just keep it at least 4" off wallYeah that will work but not to close it touching
We use cookies and similar technologies for the following purposes:
Do you accept cookies and these technologies?
We use cookies and similar technologies for the following purposes:
Do you accept cookies and these technologies?