M
MedicalINFO
- 134
- 16
I hear ya on that Raider. The only thing they said they added was myco. Even if that was the case the initial flush shouldn't be anywhere near that kind of reading.
I will say this using my same feeding schedule I did get a little def when using the bcuzz vs the canna. Nothing to major and after the first week they are grooving. Weather it be beacuse I mix it with soil and the Canna Does better with that who knows. Sorry but I'm still sold on Canna.
That is interesting shit man. I appreciate the information, I might pick up some canna and run a side by side myself. Thanks again!
Ok, I finally opened that bag of B’cuzz Coco pure fiber…
http://i808.invalid.com/albums/zz2/ShadyRound4/Round%204/BcuzzCoco1.jpg
And I got some R/O ready…
http://i808.invalid.com/albums/zz2/ShadyRound4/Round%204/BcuzzCoco0.jpg
Here’s the first run-off at 355 PPM…
http://i808.invalid.com/albums/zz2/ShadyRound4/Round%204/BcuzzCoco2.jpg
Then I flushed the coco once more…
http://i808.invalid.com/albums/zz2/ShadyRound4/Round%204/BcuzzCoco3.jpg
The 2nd run-off measured 252 PPM…
http://i808.invalid.com/albums/zz2/ShadyRound4/Round%204/BcuzzCoco4.jpg
:icon_dizzy:
Since I’ve never used coco before, I’m open to suggestions on these results and a better way to flush, unless these amounts seem fine…
Hey bud... :happy Thx for the quick response! So my lights in the bloom room turn off at 7 pm... I've never really found any pros or cons to transplanting, before the flip from veg, in the morning or a couple hours before lights out... any thoughts? Also, I'm putting my clones into the coco/perlite mix and plan on using my hydroton for my seedlings since I've got a lot of experience with that medium and don't want to screw up my babies before they're sexed... I saw another thread on having a tray with some pots in coco/perlite and others in hydroton on an ebb 'n flow setup, but haven't seen a definitive answer on the pros and cons... I flood my hydroton 3 times during the 12 hr light cycle of bloom.One thing about Ebb tables and coco pots. Make sure to flush them once a week or two. ebb tables only flood up to a certain point and right above the water level will be a a buildup of salts.
I flooded that small pot while it was on the saucer and when that coco was covered in water, the saucer filled up I dumped it into the bucket. Then I took the pot and shook the excess water over the bucket... Afterwards, I dumped all that water and repeated the process. Hopefully that was the best way to catch the initial run-off... :wonderingMan you got way different readings then me. How much water did you put through your pot?
Whats up guys just checked my run off in my canna coco it went it at 5.8 ph and a ppm of 900 came out 5.5 and a ppm of 1250 what do u guys recommend i do the plant looks perfect no burns super healthy should i be concerned.THNX
Naw thats a very acceptable drift and about usually what I saw in my runoff. When handwatering I would feed, feed, flush (plain ph'd water). I say a good rule of thumb is 100-200 ppm between in and out. As far as the PH goes if you are trying to hit that target 5.8 just bump it up .2 or .3 and you will be there. But if your plants are groovy then I say listen to them.
thnx bro
We use cookies and similar technologies for the following purposes:
Do you accept cookies and these technologies?
We use cookies and similar technologies for the following purposes:
Do you accept cookies and these technologies?