11Ron11
- 131
- 43
You're using the PG/VG to extract the THC from the flower? I wonder if that repeated long-term boiling is degrading the THC?Iv been smoking a THC vape pen for the last week and really enjoy it.
It's base is 50/50 PG/VG.
Iv ordered 1 liter PG and 1 liter VG food grade liquid.
From the research Iv done I'm going to stick with 50/50 and I'm going to start with a small batch maybe a ounce or 2..
Liquid filled just above flower and double boil for 3 hours drain liquid and refill with new 50/50 mix boil another 3 hours and then drain repeat a third time and then discard of weed and filter all liquid through cheese cloth folded multiple times.
Let cool and enjoy!
My pg and vg should be delivered by Wednesday so if I'm headed toward disaster let me know..lol
It would from what I read if you exceed 200 you need to boil the water but not the liquid inside the mason jarYou're using the PG/VG to extract the THC from the flower? I wonder if that repeated long-term boiling is degrading the THC?
I've tried making pens too. shit's tough my guy but good luck and I hope you can pull it off !It would from what I read if you exceed 200 you need to boil the water but not the liquid inside the mason jar
Way tooo thick bro.. Rosin gotta be thinned to remain soluble in terps. Gotta use mass not volume.Also not 1:1. That’s way too much. 1ml of extract to .1 ml of terps
Do press your rosin ?I make my carts with a 'wax liquidizer'.
I use 1:1 rosin to liquidizer .Wax Liquidizer
Wax Liquidizer the Name says it all. Easily turn Wax into e juice - Liquidize concentrates into vape juice, e liquid, vape oil the fast and easy way. Many flavors & ingredients.www.waxliquidizer.com
Only really like the grape flavor personally.
Good stuff and less then 10 minutes from start to finish.
I've never done anything close to what OP is talking about. I just looked it up tho, and I would say use 100% PG:@Moe.Red do you make your own carts ? I have not tried yet , seems I remember u givin me a formula? I could be wrong
Check em out. I smoke/make a lot of carts. A press is a must for those diving into carts IMO. I started with distillate, but wanted a simpler/quicker method. II just re read. He never said he was using rosin. I used to make distillate that was solid. 10% terps made it work it good carts. Idk about rosin carts
My problem is I never get anywhere near what I see people doing on youtube. There is a guy that presses 1/2 pound into 60gr or 26.4%. I get about half that typically.^^^this!^^^
Would love to see a thread on this.
Hmmm.. Guess I'll have to do PG infuse then mix VG next time. Thanks for the info.I've never done anything close to what OP is talking about. I just looked it up tho, and I would say use 100% PG:
When it comes to propylene glycol (PG) and vegetable glycerin (VG), there’s no competition. VG did not infuse well at all, but with PG, we were able to get over 90% of the THC from the decarbed flower into the PG, infusing just 1 gram of decarbed flower to 1 ounce of PG.
Compare that to VG, which pulled less than 6% of the THC from the decarbed flower, infusing 1 gram of the same strain of decarbed flower into 1 ounce of VG.
Out of a total 197.8mg of available THC in the 1 gram of bud after a decarb cycle in the decarboxylator, the VG infusion only resulted in 11.34mg of THC in the one ounce of VG used. Compare that to 179.7 mg THC in the once ounce of PG.
I really don't know anything about it, I just googled it when Mosh called me in. I make carts but with a different method.Hmmm.. Guess I'll have to do PG infuse then mix VG next time. Thanks for the info.
We use cookies and similar technologies for the following purposes:
Do you accept cookies and these technologies?
We use cookies and similar technologies for the following purposes:
Do you accept cookies and these technologies?