WhtChocolate
- Posts
- 413
- Reactions
- 973
- Joined
- Aug 9, 2018
- Points
- 93
Confirmed. They will still make QB’s until out of stock. Went to purchase a QB yesterday and flipped to COB. Should be here next week!:cool:
Confirmed. They will still make QB’s until out of stock. Went to purchase a QB yesterday and flipped to COB. Should be here next week!:cool:Idk there's something going on with those 2 companies right now.i guess if you email timber you can still have qb fixtures made until stock is gone.but it's weird they took everything off the site
I would just do 4 boards around the lep no mover and call it good.
Hey @sixstring, when replacing one of your old HPS lights, did you ever consider building a smaller set up, but put it on a light mover? I'm trying to find creative ways to replace a Gavita 6/750 in a 5x5 tent. I also have an air cooled Gavita 300 LEP, but I like that light and want to keep it in the set up, unless I can build a better replacement. I was thinking a set up like your two board light on previous page, with the 300 LEP in the middle and everything on a mover.
or do 4 of these on the corners of the 300lep,drive them soft at 100w each would be bangin that 5x5 space :cool:
https://horticulturelightinggroup.com/collections/all/products/qb96-elite-v2-quantum-board-engine
Thank you! Is this correct? If I wanted one driver to power all 4 boards, I would need a HLG-480H-54. 54v to get the boards to turn on, it supplies 480w, so that's 120w available for each board, and it pulls 8.9 amps, 2 amps per board and the board is rated for 4 amps. If I wanted to get the 200w out of each board, I would need two of these drivers. Is that the right understanding?
And I dont think Mean Well's fail too often so there wouldn't be a need to buy (2) HLG-240's instead of (1) 480, is that a safe assumption?
I went and looked around, I left the driver above to still ask, but I think I need something like a HLG-480H-C2100. Because I need (54x4=216v). And this driver could do everything I typed above, not the 480-54 because it only puts out 54v and I need 216.
or do 4 of these on the corners of the 300lep,drive them soft at 100w each would be bangin that 5x5 space :cool:
https://horticulturelightinggroup.com/collections/all/products/qb96-elite-v2-quantum-board-engine
Both drivers should work. It's about how you wire your boards. Either series or parallel. With the 54 driver you would be wiring parallel if those boards take 54V with the c2100 driver you would be wiring in series.
What chips are those? They're suggesting 170-200W for that board?
Nope, spectrum dont change with newer leds out there (qb's,cobs).Thank you Toaster!! Is one way better than the other? Doesn't one way offer protection to the other boards if one blows? Or is that in the driver and doesn't have to do with how they are wired?
Are LED chips like HID bulbs, where if they arent driven hard enough they dont reach the right K temp and the spectrum changes?
Nope, spectrum dont change with newer leds out there (qb's,cobs).
Thank you Toaster!! Is one way better than the other? Doesn't one way offer protection to the other boards if one blows? Or is that in the driver and doesn't have to do with how they are wired?
Are LED chips like HID bulbs, where if they arent driven hard enough they dont reach the right K temp and the spectrum changes?
YesBoth drivers should work. It's about how you wire your boards. Either series or parallel. With the 54 driver you would be wiring parallel if those boards take 54V with the c2100 driver you would be wiring in series.
Lumileds and luminousWhat chips are those? They're suggesting 170-200W for that board?
Yes but the color shift is extremely minor and with hid lamps it's a huge change of color to dim.Wrong. CCT will shift at different power.
When wiring parallel all those boards share equal part of the current delivered by the driver. Now let's say you have 4 boards sharing 8A. If one board dies the other 3 are still gonna share those 8A so they won't be getting 2A anymore but 2.666A. So they start running at higher temp because of that and slowly start overheating. Now when another board die and you're left with 2, those get each 4A and run even hotter. So if another one of those 2 dies the last one will be getting the whole 8A and you know what comes next.
If wired in series and running constant current when one board dies there will all go out as the circuit is broken so nothing else gets harmed anymore.
At least in theory.
Regarding spectrum. You will have some CCT shift at different drive currents. With lower drive current CCT will shift towards warmer colours and with higher drive current spectrum will shift towards colder colours. The difference is not too obvious but it's there.
You could also use a hlg 600-54 to parallel 4 to 8 boards I'm sure.so many driver options,just like a qb288. Only difference is these can handle way more power
Steven said you could really max those luminous/lumi boards out if you ran a fan over the pin sinks,crazy the shit their coming out with!
We use cookies and similar technologies for the following purposes:
Do you accept cookies and these technologies?
We use cookies and similar technologies for the following purposes:
Do you accept cookies and these technologies?