PK1
- Posts
- 3,459
- Reactions
- 9,286
- Joined
- Dec 25, 2020
- Points
- 263
@tobh maybe you can shine a light on this
I add Jack's part A and B, Epsom salt, potassium silica, and UC roots.i've never use the products you use, if the slime is getting more than something is not right with your water parameters. What has been added, removed or done that is causing the roots to get slimery.
I remember in DWC i had water parameter issues and i had to keep adding PH down and because of constantly adding ph down it was giving me trouble.
I add Jack's part A and B, Epsom salt, potassium silica, and UC roots.i've never use the products you use, if the slime is getting more than something is not right with your water parameters. What has been added, removed or done that is causing the roots to get slimery.
I remember in DWC i had water parameter issues and i had to keep adding PH down and because of constantly adding ph down it was giving me trouble.
im not saying you are adding anything else, im saying that the order you put those together can be the cause but again i dont know cuz i don't use those products.Uc roots goes in first, followed by silica, than Jack's part A than part B last. I just add the Epsom salt to the Jack's part A and it mixes in just fine.
That's it not adding anything else.
@tobh do you know the order that these products should be mixed. I think he is having slimming alage issues and something tells me it's either the way the products are mixed or somehow light is shining inside the buckets but im not sure.Uc roots goes in first, followed by silica, than Jack's part A than part B last. I just add the Epsom salt to the Jack's part A and it mixes in just fine.
That's it not adding anything else.
thats for sure, when he resets this he would need to clean every equipment, pipes, rez, airs tones with hydrogen peroxide or he'll be running in same issue again.First i need to say very nice setup, well done
Im not RDWC grower but NFT on bigger scale, your water temperature are to low, keep it a bit higher 69F -71F, from last root pics and your info i will say bad pathogens, root rot not yet.
As i understand thats your first grow in rdwc and before only coco, so well please take some short basic advice.
Always work very clean, sterilize all your equipment with h2o2, pipes, tanks, reservoir etc etc, avoid any contamination.
You adding at the moment things to reservoir without knowing what you dealing with, please dont do that, in best case take a water sample and bring to Lab or buy Microscope and check it by yourself, its not so hard to understand pathogens under Microscope, you can learn in quickly.
Wish you good luck and don't panic, my first NFT run kills over 120 plants, i did exactly what you do now.
Exactlythats for sure, when he resets this he would need to clean every equipment, pipes, rez, airs tones with hydrogen peroxide or he'll be running in same issue again.
then i would run a smaller system to at least understand the grow method before planting 20 girlsread through the past couple pages, and i've not anything to add. water temps are a little low, but not terrible. i've never done DWC or RDWC before, so my experience here is non-existent.
as for order of mixing, i've not worked with jacks or uc roots before. personally, what i don't see are any measures to prevent pathogens, either live like hydroguard and enzymes, or sterile like h2o2 or pool shock. personally, i won't run a live res. there are too many things that can go wrong, fast, and your solution temps become much more critical. i would go pick up some 34% h2o2 and add 5ml per gallon of solution in the system. that'll take care of anything living that you don't want living in the system.
at changeover after harvest, disassemble everything, toss out air stones or anything else like that which is impossible to confirm clean, scrub everything with antibacterial soap, rubbing alcohol, h2o2 solution, then bleach, then h2o2 again. reassemble, run the system with a high concentration of h2o2, like 10ml per gallon, flush with clean water, then should be back to a point where your issues are taken care of.
I'm running sterile or thought I was but I've got this brown looking slime now and growth is super slow in this pic these plants are on week 5 of vegSo I think his grow is going fine thus far. I run 6 strains in the same system and usually one looks a little different, but always grows. I see great white roots, excellent root structure, and no deficiencies up top. I wouldnt be keeping my ppms that high, but other than that it seems like you will be fine. None of your lower fan leafs are dying or showing issues. . .like you dont have root rot. . .
Are you sterile or live??? Are you running bbs?
Heisenberg says he now uses kangaroots, so I ordered some of that too. I dont care if I run sterile or alive I just want to have healthy plans.Sorry man, imma hydroguard guy. I have no idea how they fight this stuff in sterile systems. I do see the slight slime as to what your talking about. Id say the growth will be faster is you can get your res temps up to 72. Hard to do that in sterile
We use cookies and similar technologies for the following purposes:
Do you accept cookies and these technologies?
We use cookies and similar technologies for the following purposes:
Do you accept cookies and these technologies?