Jumping Right In! Brand New Set Up

[Goodthingsgrow]

Ok. Did it. Cut 20 new clones Off of the Bruce Banner 2.0.
With the heat mat, it holds fairly steady in the mid 70F range. I just need to get the humidity up but I think that will naturally come with the clippings in there.

 

[Grownsince95]

I took the light off of the stand and hung it from the ceiling. It is now providing 4K lux at the dome and 3k inside. I can lower it as I need to.

My cuttings can only wish they got that much love and attention! ❤❤

Sweet!

 

[Aqua Man]

I took the light off of the stand and hung it from the ceiling. It is now providing 4K lux at the dome and 3k inside. I can lower it as I need to.

75-80f and 80RH. You got that light set perfectly. If ya manage the others im betting 7 days till nice roots and probably 100% success.

 

[Goodthingsgrow]

I took them from the BB because it was taller. It was putting out a strong smell and the blades we’re getting sticky already.
There are so many more clones available in here. The next ones will be the New. I think I will stick those into the Turbokloner.

 

[Goodthingsgrow]

How do I get the humidity to climb or will it naturally?
The meter is showing 33% but it’s soaked in there.
I turned the mat up 3* to get the temp to rise hopefully a couple degrees.
will check them tomorrow.

 

[Goodthingsgrow]

They have all stood right up again already. This little one was very limp earlier.

 

[Aqua Man]

They have all stood right up again already. This little one was very limp earlier.

They in a cold room?

 

[Goodthingsgrow]

Yes. Just under 64F down there. 46% humidity

 

[Aqua Man]

Yes. Just under 64F down there. 46% humidity

Thats why the condensate because the air right at the wall of the dome is hitting 100% humidity cause its colder. If ya have the dome on and cubes damp with heat mat it will climb over time... just don't open it but may want to open vents a bit if it goes much jver 90%

 

[Goodthingsgrow]

Should the probe be closer to the centre of the tray?
Right now it’s just inside at the edge.

 

[Aqua Man]

Should the probe be closer to the centre of the tray?
Right now it’s just inside at the edge.

Yeah middle is best... will give the most accurate. Caution with a heat mat the cubes may dry quickly so just keep en eye but don't keep them soaking either.

 

[Goodthingsgrow]

Thank you for your time Aqua Man.
Am I better off using a sprayer or a syringe to moisten the cubes when needed?

 

[Hortulanus]

Thank you for your time Aqua Man.
Am I better off using a sprayer or a syringe to moisten the cubes when needed?

by the looks of it you did a great job man!
Leave those cuts alone as much as possible.

if the inside of the dome gets dry you can spray some water. I find my most successful clones are ones I never touch once they are set.

 

[Goodthingsgrow]

I should not spray daily?

 

[Hortulanus]

I should not spray daily?

i dont. I think the concern is (especially in your grow area) is swinging the humidity and temp when you are opening the dome too often.

 

[Goodthingsgrow]

ok. I will only spray when the dome gets dry. I will only open it to check the starter cubes daily. To watch they don’t dry out.
yes the temps drop quickly.
thank you Hortulanus.

 

[Goodthingsgrow]

How about a light cycle?
24hr or 18-6?

 

[Aqua Man]

How about a light cycle?
24hr or 18-6?

18/6 is what I prefer. Anyway ya water will work. Just don't keep em soaked or let em dry.... the word moist comes to mind....

 

[Goodthingsgrow]

I have the temp sitting steady at 76F but I can’t get the humidity up.
Some are leaning a bit limp.

 

[Grownsince95]

I have the temp sitting steady at 76F but I can’t get the humidity up.
Some are leaning a bit limp.

So that has a probe in the dome only showing 31% ?